看国产到性色 I 99re视频在线 I 婷婷久久综合九色综合伊人色 I 国内在线观看一区二区三区 I 成人 亚洲 激情 I 久久久综合网站 I 西野翔中文久久精品国产 I 国产日韩精品入口 I 国产欧美精品一区二区色综合朱莉 I 国产精品天美传媒 I 中文字幕一级片 I 538国产精品一区二区在线 I 99热免费精品 I 999日韩在线 I 精品无人区乱码1区2区3区在线 I 台湾中文性娱乐 I 视频一区视频二区中文 I 免费福利片在线观看 I 色综合91久久精品中文字幕 I 亚洲深夜影院 I 性欧美办公室18xxxxhd I 欧美一区二区二区 I 欧美日韩理论 I 精品国产一区二区三区性色av I 日韩午夜小视频 I 美女亚洲一区 I 中文字幕精品视频 I 美女掰开逼逼 I 人人澡人人射 I 欧美激情久久久 I 91精品国产综合久久小美女 I 亚洲视频在线观看 I 91视视频在线观看入口直接观看www

LCD splicing screen is one of the most popular display screens currently favored by users. The LCD splicing wall composed of splicing screens will encounter unclear image display in actual operation, while the large-screen image of LCD splicing wall is not clear. : low brightness, poor edge focusing, ghosting (image smearing), interference fringe stacking (signal source resolution is too high) or image jagged (drop frame), LCD splicing wall no screen display (no signal screen display) ) and so on. Then, when the above phenomenon occurs, how should the maintenance personnel debug the LCD splicing wall?

The splicing screen wall shows the blue bottom:

  First of all, you need to understand why the splicing screen shows the blue background because of the cockroaches Regardless of the entire splicing screen wall or the single splicing screen unit showing the blue background, it means no signal. Therefore, when a single screen displays a blue background, it may be that the software settings, signal processor to screen signal line interface is loose or the wire is defective, check the interface for looseness, or change the line test. When the entire splicing wall is blue or multiple screens display the blue bottom, the problem is most likely the problem of the signal processor and the signal output device, and the second may be the poor connection of the signal line and the interface. In this case, you need to check the software settings, signal processor, signal output device, signal interface, signal line until you find the problem.

Splicing screen wall black screen:

  The black screen of the LCD splicing screen may be caused by the following problems: the setting parameters of the splicing software are incorrect, the driving board of the splicing screen is broken, the LCD screen is damaged, and the power board is damaged. We check according to these 4 points, the black screen of the splicing screen may be unpowered, or the splicing screen may be closed by software or remote control to eliminate whether it is hardware damage.

Debugging LCD video wall image display is not clear:

  Firstly, the segmentation check can be performed on the LCD splicing wall to find out the problem. First, check whether the resolution of the LCD splicing wall signal source is consistent with the resolution of the display terminal. If it is a video signal, it depends on whether the system can In accordance with the display terminal, if the requirements of the display terminal are not met, the nature of the signal can be changed by swapping the device or adding a conversion device.

  Secondly, looking at the bandwidth of the splitter and matrix switcher and its impedance to the signal source, whether the loss of the image can be minimized within the range of the standard distance. Finally, see if the focus and convergence of the display device is normal, and whether the signal processing circuit is good.

  In addition, if the LCD splicing screen image is ghosted, you need to check whether the transmission cable is too long or too thin. The solution is to change the line or add a signal amplifier and other equipment. If the focus is not good, you can adjust the display terminal and so on.